preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 1 of 9 rev: 29oct2010 vs-509 dual frequency vcso features ? industry standard package, 9.1 x 13.8 x 3.1 mm ? 5 th generation asic technology for ultra low jitter 125 fs-rms (f n = 622.08 mhz, 12 khz to 20 mhz) 120 fs-rms (f n = 622.08 mhz, 50 khz to 80 mhz) ? output frequencies from 150 mhz to 1000 mhz ? spurious suppression, 90 dbc typical ? 3.3v supply voltage ? lvpecl or lvds output configurations ? tri-state frequency select (f1, od, f2) ? compliant to ec rohs6 directive applications pll circuits for clock smoothing and frequency translation description ? sonet / sdh ? otn (optical transport network) ? 10 gbe (gigabit ethernet) ? 10 gfc (gigabit fibre channel) ? 40 gbe & 100 gbe ? synchronous ethernet ? wimax standard gr-253-core itu-t g.709/y.1331 ieee 802.3ae incits 364-2003 ieee 802.3ba itu-t g.8261 ieee 802.16 vcc coutput output gnd fs vc saw 1 x=1,2,4 lvpecl lvds 1 x saw 2 description the vs-509 is a voltage contro lled saw oscillator that operates at the fundamental frequency from one of the two internal saw filters. the saw filters are high-q quartz devices that enable the circuit to achi eve low phase jitter performance over a wide operating temperature range. a divider circuit is deployed for output frequencies less than 600 mhz. the selectable dual oscillator is housed in a hermetically sealed leadless surface mount package and offered on tape and reel. it has a tri-state frequency select function that provides one of three conditions: frequency 1, ou tput disable, or frequency 2. pb
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 2 of 9 rev: 29oct2010 electrical performance: 3.3v lv-pecl parameter symbol minimum typical maximum units notes frequency nominal frequency f n 150 1000 mhz 1,2,3 absolute pull range apr 50 ppm 1,2,3,9 linearity lin 7 % 2,4,9 gain transfer (low / standard) k v +300 / +365 ppm/v 2,9 temperature stability f stab 100 ppm 1,7 supply voltage ( 10%) v cc 2.97 3.3 3.63 v 2,3 current (typical 50 ? load) i cc 73 ma 3 current (no load) i cc 60 75 ma 3 outputs mid level v cc -1.5 v cc -1.3 v cc -1.1 mv 2,3 single ended swing 750 mv-pp 2,3 differential swing 1.5 v-pp 2,3 current i out 20 ma 7 rise time t r 180 250 ps-pp 6,7 fall time t f 180 250 ps-pp 6,7 symmetry sym 45 50 55 % 2,3 spurious suppression 85 90 dbc 7 jitter (600 f n 1000) j 150 fs-rms 7,8 jitter (300 f n 500) j 190 fs-rms 7,8 jitter (150 f n 250) j 280 fs-rms 7,8 control voltage input impedance (f1 or f2 enabled) z c 167 k 7 input impedance (o utput disabled) z c 472 k 7 modulation bandwidth bw 200 khz 7 operating temperature t op -40 +85 c 1,3 package size 9.1 x 13.8 x 3.1 mm 1. see standard frequencies and ordering information (pg 8). 2. parameters are tested with production test circuit (pg 3). 3. parameters are tested at ambient temperature with test limits guard-banded for specified operating temperature. 4. measured as the maximum deviation from the best straight-line fit, per mil-0-55310. 5. the vc model is described below (fig 1). 6. parameters are described with waveform diagram below (fig 2). 7. not tested in production, guaranteed by design, verified at qualification. 8. for frequencies > 600 mhz, jitter is integrated across 50 khz to 80 mhz. for frequencies < 600 mhz, jitter is integrated across 12 khz to 20 mhz. (both per gr-253-core issue3). 9. tested with vc = 0.3v to 3.0v. figure 1. vc model ? f1 or f2 enabled figure 2. 10k lv-pecl waveform t a t b t r t f 80% 20% vcc-1.5v vcc-1.3v vcc-1.1v vcc=+2v sym = 100 x t a / t b - + vc 167k ? 1.65v 3pf
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 3 of 9 rev: 29oct2010 absolute maximum ratings parameter symbol ratings unit power supply v cc 0 to 6 v input current i in 100 ma output current i out 25 ma voltage control range v c 0 to v cc v frequency select fs 0 to v cc v storage temperature t str -55 to 125 c soldering temperature / duration t peak / t p 260 / 40 c / sec stresses in excess of the absolute maximum ratings can permanently damage the device. also, exposure to these absolute maximum ratings for extended periods ma y adversely affect device reliability. functional operation is not implied at these or any other conditi ons in excess of those represented in the operational sections of this datasheet. permanent damage is also po ssible if any device input (vc or fs) draws >100 ma. test circuits & output load configurations 240 0.01 f gnd fs vc 0.10 f +3.3v 240 100 z = 50 z = 50 coutput vcc output gnd vc fs output 240 34 240 coutput 2 1 5 6 vcc coutput output vc vcc lv-pecl to lv-pecl: for short transmission lengths, the pull down resistor values shown provide reasonable power consumption and waveform performance. functional test: allows use of standard power supply biasing configuration. pull down resistors are used for lv-pecl outputs and are removed for with lvds outputs. since the lvds outputs are ac coupled, the output dc levels cannot be measured. lvds to lvds: the 100 resistor should be removed if this load is provided internally within the lvds receiver. gnd output z = 50 coutput fs vc vcc z = 50 production test: dc levels shown for vee, oselect, & vc are for devices configur ed for 3.3v operation. lv-pecl outputs are dc coupled to 50 test equipment. lvds outputs are connected to a digital volt meter, then ac coupled to the test equipment. the digitial volt meter allows for mid level & swing measurements. 0.01 f 0.01 f 100 -1.3v + - + - fs vee 10k 10k 0.01 f 0.01 f dmv vee v vc (-3.00v to -0.30v) fs m (-1.90v to -1.40v) h (-0.55v to 0.00v) l (-3.30v to -2.75v) 0.01 f 0.10 f +3.3v 0.01 f 0.10 f +2.0v 0.01 f 0.10 f +3.3v or 34 2 1 5 6 34 2 1 5 6 34 2 1 5 6
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 4 of 9 rev: 29oct2010 typical characteristics: vc pull, vc pull linearity, & vc pull slope -800 -700 -600 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 700 800 0.00 0.30 0.60 0.90 1.20 1.50 1.80 2.10 2.40 2.70 3.00 3.30 control voltage (v) frequency (ppm) f1 f2 upr guardband lwr guardband total pull 1004 ppm gain transfe r 364.4 ppm/v freq @1.65v 100 ppm 985 367.4 100 f1 f2 (0.3v to 3.0v) (0.3v to 3.0v) v c pull -10% -8% -6% -4% -2% 0% 2% 4% 6% 8% 10% 0.00 0.30 0.60 0.90 1.20 1.50 1.80 2.10 2.40 2.70 3.00 3.30 control voltage (v) frequency (%) f1 f2 upr limit lwr limit 2.43% -2.90% f1 f2 min max 1.22% -3.12% (0.3v to 3.0v) (0.3v to 3.0v) vc pull linearity 0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 0.00 0.30 0.60 0.90 1.20 1.50 1.80 2.10 2.40 2.70 3.00 3.30 control voltage (v) vc slope (ppm/v) f1 f2 465.2 264.4 1.76 min ppm/v max ppm/v ratio f1 f2 (0.3v to 3.0v) (0.3v to 3.0v) (0.3v to 3.0v) 478.1 270.7 1.77 vc pull slope
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 5 of 9 rev: 29oct2010 typical characteristics: phase noise & jitter -160 -150 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 100 1,000 10,000 100,000 1, 000,000 10,000,000 100,000,000 offset (hz) l(f) (dbc/hz) f1 f2 12k - 20m 50k - 80m offset (hz) f1 (dbc/hz) f2 (dbc/hz) 10 100 1k 10k 100 k 1m 10m 100m -33.9 -62.3 -87.8 -110.4 -131.2 -148.6 -149.9 -150.2 -33.4 -62.3 -87.6 -109.9 -130.8 -147.7 -148.7 -148.6 phase noise 118.4 110.7 117.9 118.0 12k-20m 50k-80m interval (hz) f1 (fs) f2 (fs) jitter
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 6 of 9 rev: 29oct2010 25 217 200 150 260 temperature (degc) time (sec) t s t amb-p t l t p r up r dn reliability vi qualification includes aging at various extreme temper atures, shock and vibration, temperature cycling, and ir reflow simulation. the vs-509 family is c apable of meeting the following qualification tests: environmental compliance parameter conditions mechanical shock mil-std-883, method 2002 b mechanical vibration mil-std-883, method 2007 a solderability mil-std-883, method 2003 gross and fine leak mil-std-883, method 1014 resistance to solvents mil-std-883, method 2016 moisture sensitivity level ipc/jedec j-std-020, msl1 handling precautions although esd protection circuitry has been designed into the vs-509 proper precautions should be taken when handling and mounting. vi employs a human body model (hbm) and a charged-device model (cdm) for esd susceptibility testing and desi gn protection evaluation. esd ratings model minimum conditions human body model 2000 v mil-std 883, method 3015 charged device model 1000 v jedec, jesd22-c101 machine model 200 v jedec, jesd22-a115-a reflow profile (ipc/jedec j-std-020) parameter symbol value preheat time t s 60 sec min, 180 sec max ramp up r up 3 o c/sec max time above 217 o c t l 60 sec min, 150 sec max time to peak temperature t amb-p 480 sec max time at 260 o c t p 20 sec min, 40 sec max ramp down r dn 6 o c/sec max the vs-509 is qualified to meet the jedec standard for pb-free assembly. the temperatures and time intervals listed are based on the pb-free small body requirements. the temperatures refer to the topside of the package, measured on the package body surface. the vs-509 should not be subjected to a wash process that will immerse it in solvents. no clelan is the recommenced procedure. the vs-509 is designed for pick and place soldering. it should be reflowed once on topside position only. terminal plating: enig per ipc-4552 electroless ni = 3 - 6 m immersion au = 0.05 m min
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 7 of 9 rev: 29oct2010 outline & marking diagram suggested pad layout mm [inch] 123 4 5 6 13.800.15 [.543.006] 9.100.15 [.358.006] vs509 yww ccc-cccc xx/xx 3.030.15 [.119.006] 0.76 [.030] 0.79 [.031] 1.02 [.040] 2.54 [.100] 6.000.15 [.236.006] 1.55 [.061] y = year ww = week c = option codes xx = frequency codes (see ordering info) 7.62 [.300] 12.70 [.500] 0.51 [r0.020] 2.24 [.088] mm [inch] 8.80 [.346] 1.27 [.050] 2.54 [.100] 5.08 [.200] 3.00 [.118] pin out frequency select ( tri-state lv-cmos ) pin symbol function fs voltage range result 1 v c control voltage h (5v cc / 6) to v cc f2 2 fs frequency select m (v cc / 2) 15%(v cc / 2) od 3 gnd case and electrical ground l gnd to (v cc / 6) f1 4 output output 5 coutput complementar y output lv-cmos tri-state control 6 v cc power supply voltage floating fs result s in f2 (vs550 compatibility) or in od (vs709 compatibility), see order options tape and reel (eia-481-2-a) po w a n f p1 w1 w2 c b ?do d pin id pull off direction tape dimensions (mm) reel dimensions (mm) dimension w f do po p1 a b c d n w1 w2 # per tolerance typ typ typ typ typ typ min typ min min typ max reel vs-509 24 11.5 1.5 4 12 330 1. 5 13 20.2 100 24.4 30.4 200
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 8 of 9 rev: 29oct2010 standard frequencies (mhz) 155.520000 m2 156.250000 m3 161.132813 m4 166.628572 m5 167.331646 n2 168.040678 n3 173.370748 nd 184.320000 nh 307.200000 rx 311.040000 p1 368.640000 ry 614.400000 rg 622.080000 p2 625.000000 p3 644.531250 p4 657.421875 pb 666.514286 p5 669.326582 r3 672.162712 r5 690.569196 r4 693.482991 r6 696.421478 v1 696.614900 v8 707.352650 tc 718.863800 v6 737.280000 tl 905.499558 v7 other frequencies available upon request. frequency f1 must be lower than frequency f2. frequencies f1 & f2 must be selected within one frequency range: (150 - 250),(300 - 500),(600 - 1000) ordering information vs - 509 - e c e - k a a n - p2 / p4 example1: vs-509-ece-kaan-p2/r3 example2: vs-509-ece-sban-p4/pb contact information: usa: vectron international ? 267 lowell rd. hudson, nh 03051 tel: 1-88-vectron-1 ? fax: 1-888-fax-vectron europe: landstrasse, d-74924, neckarbischofsheim, germany tel: 49 (0) 7268 8010 ? fax: 49 (0) 7268 801281 asia: 1f-2f, no 8 workshop, no. 308 fenju road, waigaoqiao free trade zone, pudong, shanghai, china 200131 tel : 86 21 5048 0777 ? fax : 86 21 5048 1881 vectron international reserves the right to make changes to the product(s) and or in formation contained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or infor mation. product family v s: vcso frequency 2 see above package 509: 9.1 x 13.8 x 3.1 mm supply voltage e: 3.3v output type c: lvpecl d: lvds operating temperature e: -40 o c to 85 o c other (future use) n: n/ a oscillator gain a: +365 ppm/v b: +300 ppm/v control logic / float condition a: l = f1, m = od, h = f2 / f2 b: l = f1, m = od, h = f2 / od absolute pull range k: 50 ppm s: 100 ppm frequency 1 see above
vs-509 dual frequency vcso preliminary data sheet vectron international, 267 lowell road, hudson, nh 03051 tel: 1-88-vectron-1 ? web: www.vectron.com page 9 of 9 rev: 29oct2010 revision history date approved description 11mar2010 jm, bw preliminary release 18mar2010 jm corrected pin1 id on outline and changed floating fs to f2 04may2010 jm changed pin1 id on cover and increased ou tline height (24 mil pcb to 31 mil pcb) 30jul2010 jm added typ low gain on pg2, float c ondition text on pg7 and its ordering option on pg8 16aug2010 jm changed standard gain to +365 ppm/v, removed vc pull plots 29oct2010 jm removed 2.5v option, added vc pull & phase noise plots
|
